Journal 013: 5 Things That Can Cause Problems When Your Track Goes to Mastering
Estimated reading time: 6 minutes
Understanding what happens across the frequency spectrum, and why getting your mix right matters more than you might think.
After more than 15 years working in mastering, I've developed a pretty good understanding of what makes a track work, what holds it back, and more importantly, why. So below are 5 things that can cause problems when your track goes to mastering
I've worked across a wide range of genres and sub-genres, from underground electronic music and drum & bass to hip-hop and everything in between. And while every track presents its own challenges, there are certain issues I regularly encounter that can make the mastering process more difficult.
The thing is, mastering isn't simply about making a track louder, adding some top-end sparkle or tightening up the low end. It's about understanding sound, understanding how frequencies interact, how dynamics behave and how all of these elements translate across different playback environments.
A mastering engineer can only work with what's presented to them. The better the starting point, the more freedom there is to enhance the final result.
So, here are five things I'd recommend paying particular attention to before sending your music off for mastering.
1. Excessive stereo information in the lows and low mids
Stereo width is a fantastic creative tool. It can introduce space, depth and movement into a mix, helping individual elements sit comfortably without everything fighting for the same space.
However, when it comes to the lower frequencies, it's important to understand how much stereo information you're introducing.
Excessive stereo information in the lows and low mids can create phase-related issues, potentially weakening the fundamental elements of your mix when summed to mono. This can be particularly problematic for kick drums, basslines and other elements that rely on a solid, consistent low-frequency foundation.
It's also worth remembering that your music won't always be listened to in ideal stereo conditions. Playback systems vary considerably, and some environments offer very little stereo separation.
The objective isn't to make everything below a particular frequency mono or remove all stereo information from your low end. It's about understanding what that stereo information is doing and whether it's helping or compromising the overall sound.
My advice: Pay particular attention to your side information when monitoring the lower frequencies. Use a correlation meter, M/S analysis or a simple mono check to identify potential issues. Don't rely solely on how wide something sounds.
2. Excessive high frequencies
A bright mix can sound exciting. It can introduce clarity, definition and presence, helping individual elements cut through and giving a track that sense of energy and detail.
But there's a difference between a mix that sounds clear and one that's simply too bright.
Excessive high-frequency energy can make a track sound harsh, brittle or fatiguing. This is particularly common when multiple elements, such as hi-hats, cymbals, distorted percussion, synths and other high-frequency content, are competing for space.
The problem is that these issues can become even more apparent during mastering.
When I'm working to improve clarity, perceived loudness and overall balance, I need to consider how the existing frequency content will respond to that processing. If the upper frequencies are already aggressive, certain mastering decisions can exaggerate the problem rather than improve it.
A track might sound perfectly acceptable in your studio, particularly if you're accustomed to hearing it repeatedly, but become uncomfortable when played louder or through a different monitoring system.
My advice: Don't confuse brightness with clarity. Listen to your mix at different volumes and pay attention to whether the high frequencies remain comfortable and controlled. If they're constantly demanding your attention, there's a good chance they're doing too much.
3. Excessive low frequencies
We all love a big low end. Whether it's a powerful kick drum, a deep sub or a weighty bassline, those frequencies are often fundamental to the energy and identity of a track.
But more low end doesn't necessarily mean more impact.
Excessive low-frequency energy can consume valuable headroom, making it more difficult to achieve the desired loudness without compromising dynamics, transient detail or overall balance.
It can also create masking issues, where different low-frequency elements compete with one another, resulting in a mix that sounds muddy, congested or lacks definition.
One of the biggest misconceptions is that increasing the level of your sub or bass will automatically make your track sound bigger. In reality, a controlled low end will often translate with much more power and definition than one that's simply louder.
It's also important to understand that low frequencies behave differently depending on the listening environment. Room acoustics, speaker placement and monitoring systems can all influence how you perceive the low end.
What sounds perfectly balanced in one room might be completely different somewhere else.
My advice: Pay attention to the relationship between your kick and bass. Check for unnecessary sub-frequency energy, masking and excessive buildup. A well-controlled low end gives your mastering engineer far more room to work.
4. An imbalanced mix
This is one of the most important points, and arguably one of the most overlooked.
Mastering isn't mixing.
When a track arrives for mastering, I'm generally working with a finished stereo file. I don't have independent control over your kick, snare, bass, percussion, synths, vocals or effects.
If your kick is overpowering the bass, your hi-hats are too prominent, or certain elements are masking others, I'm working with the combined result of those elements rather than the individual tracks.
There are tools and techniques that allow me to make targeted adjustments to particular frequency ranges, but these aren't a replacement for getting the fundamental mix balance right.
For example, reducing energy in a particular frequency range might help control an overly prominent element, but it could also affect other sounds occupying that same range.
This is why understanding the relationship between individual elements is so important.
A good master starts with a mix where everything has its place, where the important elements work together and where the overall balance reflects the creative intention of the track.
My advice: Step away from your mix occasionally. Listen with fresh ears, pay attention to the relationship between individual elements and use reference tracks to help assess your overall balance. Don't assume that because you've spent hours getting everything sounding good, there isn't room for improvement.
5. Excessive limiting and processing on the master bus
This is something I encounter quite regularly, particularly with producers who want their mixes to sound as loud and finished as possible before they even reach mastering.
There's absolutely nothing wrong with using processing on your master bus. Compression, saturation, clipping and limiting can all play an important role in shaping the sound of a track.
Sometimes that processing is an essential part of the production, and removing it would fundamentally change the character of the music.
The problem arises when processing is being used excessively or simply to achieve more loudness.
Heavy limiting and clipping can reduce transient detail, restrict dynamic movement and introduce distortion. Once that information has been significantly altered, there are limitations to what can be recovered during mastering.
If a kick drum has lost its initial impact because it's been heavily clipped, for example, I can't simply turn that transient back up without considering the rest of the signal.
This doesn't mean you need to send your mix with absolutely nothing on the master bus, nor does it mean every track needs to have huge amounts of dynamic range.
It's about understanding what your processing is doing and whether it's genuinely contributing to the sound you're trying to achieve.
My advice: If your master bus processing is an intentional part of your sound, keep it. If you're using it purely to make your mix louder, consider whether it's necessary. Always listen to what the processing is doing to the transients, dynamics and overall character of your track.
Understanding the mix is understanding the master
There's a common misconception that mastering is simply the final stage of making a track sound louder, wider and more polished.
But there's considerably more to it than that.
After 15+ years of mastering, what I believe sets my approach apart isn't simply my ability to operate the equipment or use the latest processing tools. It's my understanding of sound itself.
I understand frequencies, how they interact, how they behave and how they translate across different environments, genres and sub-genres.
More importantly, I understand how to identify problems, why they're happening and what needs to be done to address them.
And I don't believe that knowledge should stop at the mastering stage.
If I identify something in your mix that's compromising the final result, I'll explain what I'm hearing, why it's happening and, where appropriate, how you can address it in your next mix.
Because the relationship between mixing and mastering is incredibly important. The better you understand what's happening during the mixing process, the better the results you can achieve when your music reaches mastering.
My job isn't just to make your music louder. It's to understand your sound, identify what's holding it back and bring out the best possible result.
Need your music professionally mastered?
At Eleven One One Audio, I offer professional mastering for producers and artists looking to get their music sounding its best and ready for release.
Whether you're working on your first release or your hundredth, every track deserves the same attention to detail.
Your mix. My job.
⸻
Raff Di Renzo
Founder, Eleven One One Audio



Comments